德國進口離心油泵

德國進口離心油泵 進口離心油泵廠家 進口離心油泵價格Centrifugal oil pump

德國KAYSEN凱森進口羅茨風機概述
離心油泵的主要過流部件有吸水室、葉輪和壓水室。通過改變泵過流部件材質、密封形式和增加冷卻系統用于輸送熱水、油類、腐蝕性或含磨粒的介質。

主要特點：
●葉輪是離心泵的核心部分，它轉速高輸出力大，葉輪上的葉片又起到主要作用，葉輪在裝配前要通過靜平衡實驗。葉輪上的內外表面要求光滑，以減少水流的摩擦損失。
●泵體也稱泵殼，它是水泵的主體。起到支撐固定作用，并與安裝軸承的托架相連接。
●泵軸的作用是借聯軸器和電動機相連接，將電動機的轉距傳給葉輪，所以它是傳遞機械能的主要部件。
●軸承是套在泵軸上支撐泵軸的構件，有滾動軸承和滑動軸承兩種。滾動軸承使用牛油作為潤滑劑加油要適當一般為2/3～3/4的體積太多會發熱，太少又有響聲并發熱！滑動軸承離心泵結構使用的是透明油作潤滑劑的，加油到油位線。太多油要沿泵軸滲出并且漂*，太少軸承又要過熱燒壞造成事故！在水泵運行過程中軸承的溫度zui高在85度一般運行在60度左右，如果高了就要查找原因（是否有雜質，油質是否發黑，是否進水）并及時處理！
●密封環又稱減漏環。葉輪進口與泵殼間的間隙過大會造成泵內高壓區的水經此間隙流向低壓區，影響泵的出水量，效率降低！間隙過小會造成葉輪與泵殼摩擦產生磨損。為了增加回流阻力減少內漏，延緩葉輪和泵殼的所使用壽命，在泵殼內緣和葉輪外援結合處裝有密封環，密封的間隙保持在0.25～1.10mm之間為宜。
●填料函主要由填料，水封環，填料筒，填料壓蓋，水封管組成。填料函的作用主要是為了封閉泵殼與泵軸之間的空隙，不讓泵內的水流不流到外面來也不讓外面的空氣進入到泵內。始終保持水泵內的真空！當泵軸與填料摩擦產生熱量就要靠水封管住水到水封圈內使填料冷卻。保持水泵的正常運行。所以在水泵的運行巡回檢查過程中對填料函的檢查是特別要注意！在運行600個小時左右就要對填料進行更換。

主要優點：
●水力模型*，效率高，性能范圍廣
●泵運行平穩，噪音低
●軸為全封結構，確保了不與介質接觸，不銹蝕，使用壽命長
●軸封采用軟填料密封或機械密封，密封安全可靠、結構簡單，維修方便快捷

主要應用：
●工業
●油管道
●輪船
●遠距離供油
●碼頭配套
 

Germany KAYSEN Kaisen imports Roots blower overview
The main flow components of the centrifugal pump are the suction chamber, the impeller and the pressurized water chamber. By changing the pump flow components, the seal form and the additional cooling system are used to deliver hot water, oil, corrosive or abrasive particles.

main feature:
● Impeller is the core part of the centrifugal pump, its high output speed, impeller blades play a major role, the impeller in the assembly before the static balance through the experiment. The inner and outer surfaces of the impeller require smoothness to reduce the friction loss of the water flow.
The pump body is also called the pump housing, which is the main body of the pump. To support the fixed role, and with the installation of the bearing bracket connected.
● The role of the pump shaft is connected by the coupling and the motor, the motor torque to the impeller, so it is the main component of the transmission of mechanical energy.
● bearing is set on the pump shaft to support the pump shaft components, there are two kinds of rolling bearings and sliding bearings. Rolling bearings using butter as a lubricant to the appropriate general 2/3 ~ 3/4 of the volume will be too much heat, too little sound and fever! Sliding bearings Centrifugal pump construction using a transparent oil as a lubricant, refueling to the oil level line. Too much oil to seep from the pump shaft and drift *, too little bearing and overheating caused by the accident! In the process of running the pump bearing the maximum temperature of 85 degrees in the general operation of about 60 degrees, if the high will find the reason (whether there is impurities, whether the black oil, whether the water) and timely treatment!
● seal ring, also known as leakage ring. Impeller inlet and pump between the gap between the pump caused by high pressure area of ??the water flow through the gap to the low pressure area, affecting the pump out of water, reduce efficiency! The gap is too small will cause the impeller and pump shell friction wear. In order to increase the return resistance to reduce the internal leakage, delay the life of the impeller and pump shell, in the pump shell and the impeller at the outer joint with a sealed ring, sealed gap between 0.25 ~ 1.10mm is appropriate.
● packing material mainly by the filler, water ring, packing tube, packing gland, water sealing tube composition. The function of the stuffing box is mainly to close the gap between the pump housing and the pump shaft, so that the water inside the pump does not flow outside to prevent the outside air from entering the pump. Always keep the vacuum inside the pump! When the pump shaft and the filler friction heat is necessary to rely on water seal tube water to the water ring so that the filler cooling. Maintain the normal operation of the pump. So in the operation of the pump during the tour inspection of the stuffing box is to pay special attention! It takes about 600 hours to replace the packing.

Key Benefits:
● Advanced hydraulic model, high efficiency, wide range of performance
● Pump running smoothly, low noise
● Shaft is fully enclosed structure, to ensure that no contact with the media, no corrosion, long service life
● Shaft seal with soft packing seal or mechanical seal, sealed safe and reliable, simple structure, easy maintenance

main application:
●Industry
● oil pipeline
● ship
● Long distance fuel supply
● Terminal support

德國進口離心油泵 進口離心油泵廠家 進口離心油泵價格

德國KAYSEN凱森對您的承諾：

●放心的質量：從鑄件到產品，實行全過程質量監控，*檢測，責任到人！

●貼心的價格：高效成本控制，自產自銷，減少中間環節，讓利于客戶！

●快速的貨期：充足的庫存，上海便捷物流，縮短交貨期，嚴格按照合同期交貨！

Germany Kaysen commitment to you:

● Reliable quality: from casting to the product, the implementation of the whole process of quality control, all-round detection, responsibility to the people!

● intimate price: efficient cost control, production for sale, to reduce the intermediate links, to help customers!

● fast delivery: adequate inventory, Shanghai convenient logistics, shorten the delivery time, in strict accordance with the contract delivery!

進口離心油泵廠家 進口離心油泵價格