THDP0100高壓差分探頭

Tektronix提供了廣泛的高壓探測解決方案，使用戶能夠安全、準確地進行浮動測量。

關鍵性能規范

帶寬高達200mhz

高達6000 V差速器(直流+ pk交流)

最多2300v普通(RMS)

關鍵特性

超量程的指標

安全認證

可切換的衰減

可切換的帶寬限制

應用程序

浮動測量

開關電源設計

電機驅動設計

電子鎮流器的設計

陰極射線管顯示器設計

電源轉換器的設計和服務

電源設備評估

連接

BNC接口(P5200A探頭)

TekVPI®接口(TMDP和THDP系列探頭)

TekProbe®接口(P5202A、P5205A、P5210A系列探頭)

安全的高壓探頭解決方案

THDP0100和P5210A具有與Tektronix的差分動態范圍能力，允許用戶安全測量高達±6000 V。THDP0100支持高達100mhz的帶寬，并在1/1000增益下轉換速率高達2500 V/ns。這些探頭有兩種尺寸的鉤頭，并有一個超量程的視覺和聽覺指示器，當它們超過探頭的線性范圍時，會發出警告。

THDP0200和P5205A是有源差分探頭，能夠安全測量高達±1500 V的差分電壓。該探頭在IGBT電路(如電機驅動器和功率轉換器)中進行測量是有效的。THDP0200支持高達200mhz的帶寬，并在1/250增益下轉換速率高達275 V/ns。

TMDP0200和P5202A適用于差動電壓高達±750 V的中壓應用。這些探頭具有較低的衰減范圍和較好的信噪比。

P5200A可與任何示波器配套使用，使用戶可以在示波器接地的情況下安全地測量浮動電路。P5200A有源差分探頭將浮置信號轉換為低壓接地信號，在任何接地示波器上都能安全、方便地顯示。

警告:為了安全操作，請勿使用帶有浮動輸入(隔離輸入)示波器的P5200A高壓差分探頭，如Tektronix TPS2000和THS3000系列示波器。P5200A高壓差動探頭需要一個示波器或其他帶接地輸入的測量儀器。

連通性選項

TMDP系列探頭與THDP系列探頭采用TekVPI®接口，實現示波器與探頭之間的智能通訊。按下探頭菜單按鈕將啟動示波器顯示上的探頭控制菜單，提供對所有相關探頭設置和控制的訪問。這些探頭的設計不需要TPA-BNC適配器就可以在TekVPI®示波器上工作。

P52xxA系列探頭配有Tektronix TekProbe®接口，該接口可將刻度信息傳遞給示波器?？梢耘c配置有TekProbe®接口的示波器直接連接，也可以與使用1103 TekProbe®電源的任何示波器直接連接。

Tektronix offers a broad portfolio of high-voltage probing solutions that enable users to safely and accurately make floating measurements.

Key performance specifications

• Bandwidths up to 200 MHz

• Up to 6000 V differential (DC + pk AC)

• Up to 2300 V common (RMS)

Key features

• Overrange Indicator

• Safety Certified

• Switchable Attenuation

• Switchable bandwidth limit

Applications

• Floating measurements

• Switching power supply design

• Motor drive design

• Electronic ballast design

• CRT display design

• Power converter design and service

• Power device evaluation

Connectivity

• BNC interface (P5200A probes)

• TekVPI® interface (TMDP and THDP Series probes)

• TekProbe® interface (P5202A, P5205A, and P5210A Series probes)

Safe high-voltage probe solutions

The THDP0100 and P5210A have the largest differential dynamic range capability from Tektronix, allowing users to safely measure up to ±6000 V. The THDP0100 supports bandwidths up to 100 MHz and slew rates up to 2500 V/ns at 1/1000 gain. These probes are supplied with two sizes of hook tips and have an overrange visual and audible indicator which warns the user when they are exceeding the linear range of the probe.

The THDP0200 and P5205A are active differential probes that are capable of safely measuring differential voltages up to ±1500 V. The probes are effective in making measurements in IGBT circuits such as motor drives and power converters. The THDP0200 supports bandwidths up to 200 MHz and slew rates up to 275 V/ns at 1/250 gain.

The TMDP0200 and P5202A are designed for medium-voltage applications with differential requirements up to ±750 V. These probes have lower attenuation ranges and offer better signal-to-noise ratio.

The P5200A can be used with any oscilloscope and enables users to safely make measurements of floating circuits with their oscilloscope grounded. The P5200A Active Differential Probe converts floating signals to low-voltage ground-referenced signals that can be displayed safely and easily on any ground-referenced oscilloscope.

Warning: For safe operation, do not use the P5200A High-voltage Differential Probe with oscilloscopes that have floating inputs (isolated inputs), such as the Tektronix TPS2000 and THS3000 Series oscilloscopes. The P5200A High-voltage Differential Probe requires an oscilloscope or other measurement instrument with grounded inputs.

Connectivity options

The TMDP and THDP Series probes are equipped with the TekVPI®interface which allows smart communication between the oscilloscope and probe. Pushing the probe menu button will launch the probe control menu on the oscilloscope display providing access to all relevant probe settings and controls. These probes are designed to operate on TekVPI®oscilloscopes without requiring the TPA-BNC adapter.

The P52xxA Series probes are equipped with the Tektronix TekProbe®interface which communicates scale information to the oscilloscope. Direct connections can be made to oscilloscopes configured with the TekProbe®interface or to any oscilloscope when used with the 1103 TekProbe®Power Supply.