碾壓制粒機Grinding Pelletizer

一、工作原理及應用范圍介紹  Introduction of Working Principle and Scope of Application

物料按配方要求，經計量、拌合、粉碎后，由皮帶輸送機輸入料斗，再定量均勻的進入造粒機。物料在造粒機容器內被呈三角形設置具有彈性的碾壓輥與均布刮料器的滾動碾壓與不斷地拌刮鋪料作用下，物料被輥輪強力塞進?？讐褐瞥蓤A柱狀從?？紫路綌D出，然后被設置于平模下面的兩把割刀割成所需要的長度，落入接料甩盤上然后由甩料盤將顆粒送出主機從而完成造粒過程。主要適用于以下物料的制粒：

(1)適用于小批量、多品種生產如農用肥料、農藥、化工、醫藥、建材等行業造粒。

(2)適用于年產5000-40000噸的中、小型復混肥料生產規模及農業化服務中心。還可以加工氯化銨、、硅鈣鎂等單質肥、泥炭、草炭、畜禽糞、有機無機復肥、稀土復肥、磁化復肥、生物復肥等。

(3)超能型擠壓造粒機可加工農藥顆粒劑、土壤調整劑、冶金增碳劑、燃氣脫硫劑、化工催化劑等。

(4)造粒直徑一般在2-8㎜，長度：3-6㎜。

     The materials will be conveyed to the hopper through the belt conveyor after being measured, mixed and smashed according to the formula, and fed in thepelletizer uniformly with fixed quantity. The materials will be rolled, ground, mixed and distributed continuously by the flexible grinding rollers and uniform discharger set in triangle shape in the pelletizer container, fed in the die hole by roller to form into cylindrical product, extruded from the lower part of the die hole, cut into the required length by two cutters under the flat die, dropped in the collecting disc, and finally discharged out from the main machine by dump disc, thus to complete the pelleting. The equipment is mainly applicable to pelleting of following materials:

(1)  Small batch and multiple-product production, such as agricultural fertilizer, pesticide, chemical, medicine and construction material industries.

(2) Medium and small-sized compound fertilizer production with annual output of 5,000-40,000t and agricultural service center; processing of compound fertilizer, potassium chloride, silicon calcium magnesium and other single elementfertilizer, peat, turf, animal manures, organo-inorganic fertilizer, rare earth compound fertilizer, magnetization compound fertilizer, and biological compound fertilizer.

(3)  The super extruding pelletizercan be used for process of the pesticide granules, soil modifier, metallurgical recarburizer, gas desulfurizer and chemical catalyst.

(4)   Pelleting diameter of 2-8mm and length of 3-6mm.

二、特點Characteristics

1.投資省、上馬快、占地面積小，能耗低，經濟效益高。

2.顆粒成粒率可達90％，不需再干燥、無篩粉、無返料。

3.顆粒有足夠的強度，不結塊，流動性好。

4.操作方便，使用安全，可靠性好等特點。

1.It is less in investment, fast in put into production, small in floor area, low in energy consumption and high in economic efficiency.

2.The yield rate of granule is up to 90% without drying, screening and returning charge.

3.The granules are enough in strength and good in mobility without caking.

4.It is convenient for operation, safe in application and good in reliability.

三、技術參數（下表中數值僅供選型時參考）

Technical parameters (the values in the table below are for reference in type selection only)

四、工藝流程圖Process flow diagram

碾壓制粒機