進口化工流程泵｜美國進口化工流程泵

  進口化工流程泵｜美國化工流程泵

進口化工流程泵優點:

葉輪可用閉式、半開式、開式三種?？奢斔颓鍧?，含顆粒，含少量氣體介質。也可輸送高溫、低溫、強腐蝕介質。葉輪設有平衡孔加耐腐環，平衡軸向力。 　2 泵體和軸承架用中間連接段連接。根據不同的工況條件，中間連接段可采用不同的材質，避免輸送強腐蝕介質時軸承架、軸承嚴重腐蝕。同時中間連接段設有水冷腔，通冷卻循環水，阻隔高溫介質將高溫傳到軸承上。 　3 密封形式可采用填料密封，單、雙端面機械密封，集裝式單端面機械密封。根據不同情況和用戶對冷卻與沖洗要求?！? 軸承架設計有空冷散熱片、風冷風扇、水冷腔三種形式，用戶可根據使用工況選用。軸承由油環從油箱里濺稀油潤滑。油箱內的油由水冷腔的水冷卻，軸承內的熱由冷水帶走，以保證軸承隨時處于正常工作狀態。 　5 根據介質溫度和壓力等情況，支撐形式采用中心支撐和腳架支撐。 

進口化工流程泵工作原理:

化工泵在工作前，泵體和進料管必須罐滿液體行成真空狀態，當葉輪快速轉動時，葉片促使液體很快旋轉，旋轉著的液體物料在離心力的作用下從葉輪中飛去，泵內的水被拋出后，葉輪的中心部分形成真空區域。液體物料在大氣壓力的作用下通過管網壓到了進料管內。這樣循環不已，就可以實現連續輸送。

在化工泵啟動前，泵殼內灌滿被輸送的液體;啟動后，啟動后，葉輪由軸帶動高速轉動，葉片間的液體也必須隨著轉動。在離心力的作用下，液體從葉輪中心被拋向外緣并獲得能量，以高速離開葉輪外緣進入蝸形泵殼。

在蝸殼中，液體由于流道的逐漸擴大而減速，又將部分動能轉變?yōu)殪o壓能，zui后以較高的壓力流入排出管道，送至需要場所。液體由葉輪中心流向外緣時，在葉輪中心形成了一定的真空，由于貯槽液面上方的壓力大于泵入口處的壓力，液體便被連續壓入葉輪中?？梢?，只要葉輪不斷地轉動，液體便會不斷地被吸入和排出。

進口化工流程泵技術參數:

流量：9.5～2000m3/h          
揚程：4～160m
轉速：1450、2900r/min     
功率：1.1～160KW
口徑：32～300mm       
工作壓力：2.5MPa
工作溫度：-40～+300℃
特性曲線平坦，氣蝕值低，在不滿負荷時，也保持這些特性。

美國泰樂TYLER售后服務:
*的服務鑄就*的企業讓客戶無后顧之憂。
1、按合同要求提供產品的合格證、銘牌、檢驗報告、產地證名、安裝說明書等。
2、顧客在驗收產品過程中，如出現與合同要求不符時，我司接到顧客通知后兩小時內給予處理。
3、我司提供十二個月以上產品質保期，時間從驗收合格之日起計算。
4、在正確安裝和使用下，出現產品質量問題，本公司將負責到底。

Chemical process pump

Advantages of imported chemical process pump:

Impeller can be closed, semi open, open three. Can be cleaned clean, containing particles, containing a small amount of gas medium. High temperature, low temperature, strong corrosive medium. The impeller has a balance hole Jianai rot ring, axial force balance. 2 pump body and bearing frame with intermediate connection. According to the different working conditions, the middle connecting section can adopt different materials, so as to avoid the serious corrosion of the bearing frame and the bearing. At the same time, the middle connecting section is provided with a water cooling cavity, which is used for cooling the circulating water and blocking the high temperature medium to transfer the high temperature to the bearing. The 3 seal form can be used for single and double packing seal, mechanical seal, container type single mechanical seal. According to different conditions and user requirements for cooling and flushing. 4 bearing frame is designed with air cooling radiator, air cooling fan, water cooling cavity in three forms, users can choose according to the working conditions. The bearings are lubricated by oil rings from the oil tank. The oil in the oil tank is cooled by the cooling water, and the heat inside the bearing is taken away by cold water to ensure that the bearing is in normal working condition at any time. 5 according to the medium temperature and pressure, the central support and support leg.  

Working principle of chemical process pump:

Chemical pump before work, the pump body and the feeding pipe must be tank full of liquid into the vacuum, when the impeller rotates fast, fast rotating blades to the liquid, liquid material whirling role under the centrifugal force and flew from the impeller, pump the water is thrown, the impeller formed the center of the Ministry of vacuum area. Under the action of atmospheric pressure, the liquid material is pressed into the feed pipe through the pipe network. This endless cycle, you can achieve continuous delivery.

Before the start of the chemical pump, the pump shell is filled with the liquid to be delivered; after the start, start, the impeller driven by the high-speed rotation of the shaft, the liquid between the blades must also be with the rotation. Under the action of centrifugal force, the liquid was thrown from the impeller center and outer edge of the energy leaving the impeller at high speed into the outer pump shell shaped cochlea.

In the spiral case, the liquid due to the gradual expansion of the flow path and slow down, and some of the kinetic energy into static pressure, and finally into the discharge pipeline with high pressure, sent to the required place. The liquid from the impeller center to the outer edge of the impeller center, the formation of a certain vacuum, due to the pressure tank above the liquid level is greater than the pressure pump at the entrance, the liquid will be pressed into the impeller in a row. Visible, as long as the impeller continues to rotate, the liquid will continue to be inhaled and discharged.

Technical parameters of imported chemical process pump:

Flow rate: 9.5 ~ 2000m3/h

Head: 4 ~ 160m

Speed: 1450, 2900r/min

Power: 1.1 ~ 160KW

Diameter: 32 ~ 300mm

Working pressure: 2.5MPa

Operating temperature: -40 ~ +300 C

The characteristic curve is flat and the cavitation value is low, and these characteristics are also maintained at the time of the load.

The United States TYLER Taylor customer service service:

The first-class service created a first-class enterprise so that customers no worries.

1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..

2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.

3, our company provides more than twelve months warranty period, the time from the date of acceptance.

4, in the correct installation and use, product quality problems, the company will be responsible in the end.