進口羅茨風機美國進口羅茨風機

進口羅茨風機美國羅茨風機

進口羅茨風機工作原理：

進口羅茨風機為容積式風機，輸送的風量與轉數成比例，三葉型葉輪每轉動一次由2個葉輪進行3次吸、排氣，與二葉型相比，氣體脈動變少，負荷變化小，機械強度高，噪聲低，振動也小。在2根平相行的軸上設有2個三葉型葉輪，輪與橢圓形機箱內孔面及各葉輪三者之間始終保持微小的間隙，由于葉輪互為反方向勻速旋轉，使箱體和葉輪所包圍著的一定量的氣體由吸入的一側輸送到排出的一側。各支葉輪始終由同步齒輪保持正確的相位，不會出現互相碰觸現象，因而可以高速化，不需要內部潤滑，而且結構簡單，運轉平穩，性能穩定，適應多種用途，已運用于廣泛的領域。

進口羅茨風機技術參數：

壓力：9.8-98kpa
風量：0.49-261.9m3/min
轉速：590-2100r/min
功率：0.75kw-560kw
口徑：50-3500mm

進口羅茨風機的特點:

●由于采用了三葉轉輪及帶螺旋線型的箱體，所以風機的噪聲的振動很小。

●葉輪和軸為整體結構，且葉輪無磨損，風機性能持久不變，可以*連續運轉。

●高速高效率，且結構非常緊湊。

●結構簡單，由于采用了特殊軸承，具有超群的耐久性，使用壽命比國內風機長，且維修管理也方便

●由于附有齒輪油甩油裝置，因此不會產生漏油的現象。

進口羅茨風機轉子檢修的質量標準要求如下：

1、轉子不應有砂眼、氣孔等缺陷。

2、轉子組裝時兩端軸頸的平行度偏差應不大于0.02mm，兩端面與墻板的平行度偏差應不大于0.05 mm。當風機進出口方向和主軸位置不變時，轉子壓力角間隙應在轉子水平線成45°角兩個位置上調整。不同型號的風機轉子各部間隙不同。

3、轉子應進行動靜平衡校驗。

4、軸與轉子垂直度公差應不大于0.05 mm。

進口羅茨風機運行條件：

1、輸送介質的進汽溫度通常不得大于 40℃。

2、介質中微粒的含量不得超過 100mg/m3，微粒zui大尺寸不得超過zui小工作間隙的一半。

3、運轉中軸承溫度不得高于 95℃，潤滑油溫度不高于 65℃。

4、使用壓力不得高于銘牌上規定的升壓范圍。

5、羅茨鼓風機葉輪與機殼、葉輪與側板、葉輪與葉輪間隙出廠時已調好，重新裝配時要保證該間隙。

6、羅茨鼓風機運行時，主油箱、副油箱油位必須在油位計兩條紅線之間。

進口羅茨風機美國泰樂TYLER售后服務：

*的服務鑄就*的企業讓客戶無后顧之憂。
1、按合同要求提供產品的合格證、銘牌、檢驗報告、產地證名、安裝說明書等。
2、顧客在驗收產品過程中，如出現與合同要求不符時，我司接到顧客通知后兩小時內給予處理。
3、我司提供十二個月以上產品質保期，時間從驗收合格之日起計算。
4、在正確安裝和使用下，出現產品質量問題，本公司將負責到底。

The United States imported roots blower roots blower

The working principle of imported roots blower:

Blower for volume blower, air transport and rotation is proportional to the trefoil impeller rotating each time by 2 to three times the impeller suction exhaust gas pulsation of small, small vibration, low noise. Fan impeller on 2 axes and oval shell hole surface, impeller end and the fan cover has always maintained a small gap between, on one side of the synchronous gear drives the wind from the fan inlet along the inner wall of the shell is transported to the discharge. The inner cavity of the fan does not need lubricating oil, the structure is simple, the operation is stable, the performance is stable, and the utility model is suitable for various purposes, and can be used in a wide range of fields. The characteristics of Roots blower with three rotor structure, and reasonable housing into the inner structure of import air outlet, so the fan small vibration and low noise, the impeller and shaft for the overall structure and the performance of the fan impeller wear free, persistent, can be long-term continuous operation.

Imported roots blower installation requirements:

Fan in the environment temperature of not more than 40 degrees C, can be used for a long time. In the summer, the exhaust fan should be installed and other cooling measures to improve the service life of the fan.

Imported roots blower application:

Sewage aeration water purification plant filter backwash vacuum dust removal material conveying

Widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, metallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life. Shanghai Yi butterfly products sell well all over the country, high quality, efficient service, won the trust of users and a wide range of praise.

Imported roots blower technical parameters:

Pressure: 9.8-98kpa

Air volume: 0.49-261.9m3/min

Speed: 590-2100r/min

Power: 0.75kw-560kw

Caliber: 50-3500mm

Imported roots blower operating conditions:

The inlet temperature of 1, the transmission medium is usually not more than 40 DEG C.

The content of particles of 2 medium shall not exceed 100mg/m3, the maximum particle size should not exceed half of the minimum clearance.

3, the bearing temperature in operation shall not exceed 95 DEG C, the lubricating oil temperature is not higher than 65 DEG C.

4, shall not exceed the use of pressure boosting range specified on the nameplate.

5, roots blower impeller and casing, impeller, impeller and impeller clearance and side plate factory tuned, re assembly to ensure the gap.

6, roots blower operation, the main oil tank, fuel tank level must be two red line on the oil level between.

The United States imported roots blower tylosin TYLER customer service service:

The first-class service created a first-class enterprise so that customers no worries.

1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..

2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.

3, our company provides more than twelve months warranty period, the time from the date of acceptance.

4, in the correct installation and use, product quality problems, the company will be responsible in the end.

進口羅茨風機guan網：http://www.twvalve。。ｎｅｔ/html/2285.html