高效薄膜蒸發器

高效薄膜蒸發器的優點：
1.極小的壓力損失
在高效薄膜蒸發器中，物料流與二次蒸發汽流是兩個獨立的通道∶物料是沿蒸發筒體內壁降膜而下；而由蒸發面蒸發，蒸汽則從筒體中間的空間幾乎是*地離開蒸發器,因此壓力損失是非常小的。
2.可實現真空條件下的操作
正由于二次蒸氣由蒸發面到冷凝器的阻力很小,使得整個蒸發筒體內壁的蒸發面維持較高的真空度，幾乎等于真空系統出，口的真空度,由于真空度的提高,有效降低了被處理物料的沸點。
3.高傳熱系數,高蒸發強度
增大了與熱介質的溫度差;呈湍流狀態的液膜,降低了熱阻;同時抑制物料在壁面上結焦、結垢,也提高了蒸發筒壁的傳熱。
4.低溫蒸發
蒸發筒體內能維持較高的真空度,被處理物料的沸點大大降低,因此特別適合熱敏性物料的低溫蒸發。
5.過流時間短
物料在蒸發器內的過流時間很短,約10秒左右;對于常用的活動刮板而言,其刮動物料的端面有導流的溝槽,其斜角通常為45σ,改變斜，角的角度,可改變物料的過流時間,物料在刮板的刮動下,螺旋下降離開蒸發段。縮短過濟，有效防止產品在蒸發過程中的分解。
6.可利用低品位蒸汽
蒸汽是常用的熱介質,由于降低了物料的沸點,在保證相同4t的條件下,就可降低加熱介質溫度,利用低品位的，有利于能量的綜合。
7.適應性強,操作方便
結構設計非常特殊,使該產品可處理一些常規蒸發器不易處理的高粘庋、含顆粒、熱敏性及易結的物料。   

Advantages of a high efficiency thin film evaporator:
1. Minimal pressure loss
In the high-efficiency thin film evaporator, the material flow and the secondary vaporization flow are two independent channels: the material falls under the inner wall of the evaporation cylinder; while the evaporation surface evaporates, the steam is almost from the space in the middle of the cylinder. It leaves the evaporator unimpeded, so the pressure loss is very small.
2. Can realize the operation under vacuum conditions
Because the resistance of the secondary vapor from the evaporation surface to the condenser is small, the evaporation surface of the inner wall of the entire evaporation cylinder maintains a high degree of vacuum, which is almost equal to the vacuum system, and the vacuum degree of the mouth is effective due to the improvement of the vacuum degree. Reduce the boiling point of the material being processed.
3. High heat transfer coefficient, high evaporation strength
The temperature difference with the heat medium is increased; the liquid film in the turbulent state reduces the thermal resistance; at the same time, the material is inhibited from coking and scaling on the wall surface, and the heat transfer of the evaporation cylinder wall is also improved.
4. Low temperature evaporation
The evaporation cylinder can maintain a high degree of vacuum, and the boiling point of the material to be treated is greatly reduced, so it is particularly suitable for low temperature evaporation of heat sensitive materials.
5. Short overcurrent time
The overcurrent time of the material in the evaporator is very short, about 10 seconds; for the commonly used movable scraper, the end surface of the scraping material has a guiding groove, and the oblique angle is usually 45σ, changing the inclination and the angle. The angle can change the overcurrent time of the material. Under the scraping of the scraper, the spiral descends away from the evaporation section. Shorten the economy and effectively prevent the decomposition of the product during the evaporation process.
6. Available low grade steam
Steam is a commonly used heat medium. Because the boiling point of the material is lowered, the temperature of the heating medium can be lowered under the condition of ensuring the same 4t, and the use of low grade is beneficial to the integration of energy.
7. Adaptability and easy operation
The structural design is very special, allowing the product to handle high-viscosity, granule-containing, heat-sensitive and easy-to-knot materials that are not easily handled by conventional evaporators.