VF系列渦街流量計（旋渦型）是根據卡門旋渦原理，采用的微功耗處理器和頻譜分析的方法采集數據及*的流量儀表制造工藝技術，成功開發出智能機電一體化的新型渦街流量計。儀表常數穩定，測量范圍廣，壓力損失小，安裝及使用維護方面簡單、經濟。特別是解決了耐高溫、抗振動、微功耗等關鍵性問題。廣泛應用于封閉管道中蒸汽、氣體和液體介質的質量流量和體積流量的計量。
主要技術參數
1.測量介質：液體、氣體、過熱/飽和蒸汽
2.準確度：±1.0%、±1.5%
3.工作壓力：1.6Mpa；2.5Mpa（其它壓力，需訂做）
4.介質溫度：-30℃-60℃(常溫型）-30℃-250℃（中溫型）,-30℃-300℃（高溫型）
5.公稱口徑：DN15-DN300（管道型）DN300以上（插入式）
6.殼體材料：304不銹鋼
7.防爆標志：ExdⅡBT4;
8.輸出信號：脈沖輸出，（4-20）m電流信號，RS-485通訊接口（modbus協議）
9.安裝形式：夾接式、法蘭式
10.供電：24VDC,3.6V(電池）
■ 流量計在水平管道上的安裝Installation of flowmeter on horizontal pipelines
▲ 在水平管道上安裝是流量計常用的安裝方式
installation of flowmeter on horizontal pipelines is the most common installation mode
▲ 測量氣體流量時,若被測氣體中含有少量的液體,流量計應安裝在管線的較高處.
When the flowmeter is used to measure gas flow,if there is small amount of liquid in the gas,the flowmeter shall be installed at the higher position of the pipeline.
▲ 測量液體流量時,若被測液體中含有少量的氣體,流量計應安裝在管線的較低處
When the flowmeter is used to measure liquid flow,if there is small amount of gas in the liquid,the flowmeter shall be installed at the lower position of the pipeline.
■ 流量計在垂直管道的安裝
Installation of flowmeter on vertical pipelines
▲ 測量氣體流量時,流量計可以安裝在垂直管道上,流向不限.
When the flowmeter is used to measure gas flow,the flowmeter can be installed on the vertical pipelineａnd the flow direction is not limited.
▲ 若被測氣體中含有少量的液體,氣體流向應由上而下.
if there is small amount of liquid in the measured gas, the gas shall flow upwardly from the lower position.
▲ 測量液體流量時,液體流向應由下向上
When the flowmeter is used to measure liquid flow,the liquid shall flow upwardly from the lower position.
■ 流量計和顯示儀運行前的準備工作
Preparation before the operation of flowmeter and display meter.
▲ 仔細檢查流量計的安裝,接線等是否正確無誤.
▲ 接通顯示儀電源,觀察顯示儀是否有流量顯示.
▲ 緩慢打開閥門,到一個較小壓力時停止,觀察傳感器周圍是否有泄露現象,并觀察顯示儀是否有流量顯示
▲ .若情況正常,開大閥門,穩定一段時間后,觀察儀表顯示的流量是否正常.
▲ Check the installation of the flowmeter carefully,ａnd whether the wiring etc,is done in correct way,
▲ Connect with the power supply of the display meter,ａnd observe whether there is flow display on the display meter.
▲ Open the value slowly and stop when the pressure is relatively low.Observe whether there is leakage around the sensor,ａnd observe whether there is flow display on the display meter.
▲ If they are in normal condition,further open the value,ａnd after it is stabilized for a while,observe whether the flow displayed on the meter is normal.
,,,,,
在流體中設置非流線型旋渦發生體（阻流體），則從旋渦發生體兩側交替地產生兩列有規則的旋渦，這種旋渦稱為卡曼渦街，旋渦列在旋渦發生體下游非對稱地排列。設旋渦的發生頻率為f，被測介質來流的平均速度為V，旋渦發生體迎流面寬度為d，表體通徑為D，根據卡曼渦街原理，有如下關系式:
f=StV/d
式中：
f－發生體一側產生的卡門旋渦頻率
St－斯特羅哈爾數（無量綱數）
V－流體的平均流速
d－旋渦發生體的寬度
,,,,, V
,,,,,,,,,
采購中心
