用途：主要用于電池安全性能檢測中爐熱試驗、加熱測試等。
Use: Mainly for battery safety testing in furnace heat test, heating test, etc.
特點：
Characteristics:流線型外觀設計
Streamlined design
箱門及控制面板均采用弧面流線型設計，整體美觀大方，安全可靠，不會傷及工作人員
The door and the control panel is designed with Curved streamline.The overall appearance which is elegant, safe and reliable will not hurt the staff
底部腳輪方便移動
Bottom casters for easy movement
箱體底部安裝4套萬向輪，靠前面的兩個腳輪帶自鎖功能，方便設備的移動和固定
The bottom of the chamber is equipped with 4 sets of universal wheels. There is self-locking function on the front two casters, which facilitate the movement and fixation of the equipment.
單機雙箱設計
Single machine double box design
本設備采用單機雙箱體設計，上下各一個測試箱體，兩個箱體的控制系統及冷凍系統獨立運行
This equipment adopts a single-seat double-casing design with one test case up and down, two control systems and freezing systems being operated independently
前門二次防爆設計
Front door secondary explosion-proof design
箱體的前面和后面泄壓門均加裝防爆鏈，當電池爆炸造成極大的沖擊力將設備門沖開時，防爆鏈起到緩沖作用，防止門打開或者沖掉飛出，以防止造成二次傷害
The front and rear pressure relief doors of the chamber are equipped with anti-explosion chain. When the battery explosion causes a great impact force to open the equipment door, the explosion-proof chain acts as a buffer to prevent the door from opening completely or flushing out to prevent Cause secondary damage
加強型合頁和防爆鎖設計
Reinforced hinge and explosion lock design
防爆門與箱體之間連接的合頁采用加強型304#不銹鋼，同時，門鎖采用強力平面鎖，確保設備的安全。
The Explosion-proof door and the chamber connection are reinforced with 304# stainless steel while the door lock is adopted of a strong plane lock to ensure the safety of the equipment.
側面防爆泄壓設計
Side explosion pressure relief design
每個箱體側面安裝自動防爆泄壓口，一旦感應壓力自動泄壓
Each side of the chamber is equipped with an automatic explosion relief vent, once the pressure is automatically relieved.In case inducing pressure ,it is automatically relieved.
性能參數：
型號 ModelBTT-D2-216A
BTT-D2-360A
單層內箱尺寸Single-layer inner box size
W600 X D600 X H600 MM
W1000 X D600 X H600 MM
外箱尺寸
External chamber size
W1340*D1085*H1765mm
結構方式結構方式Structural pattern
試驗箱設計為整體式上下二個工作室結構
The test chamber is designed as a monolithic upper and lower box structure
溫度范圍 Temperature range
室溫+10℃-+150℃Room temperature +10℃-+150℃
溫度波動度Temperature range
±0.3℃
升溫時間Heating time
RT+10～+100℃ 10分鐘左右 RT+10～+100°C for about 10 minutes
溫度均勻度Temperature uniformity
≤±2℃ （空載、恒定狀態(tài)時）
≤±2℃ （No load, constant state)
觀察視窗
Observation windowW300 X H300 MM,防爆玻璃并貼有防爆膜
Explosion-proof glass with explosion-proof membrane
冷卻方式
Cooling method
風冷
Air cooling
控制方式
Controlling method觸摸屏可程式控制PLC、帶USB接口、帶RJ485接口可連接電腦控制，專用的網絡控制軟件，方便遠程監(jiān)控，數據采集
Touch screen programmable control PLC, with USB interface, with RJ485 .interface can be connected to computer control, special network control software, convenient remote monitoring, data acquisition
內箱材質
Inner chamber materialSUS304#鏡面不銹鋼，1.0MM厚，噴鐵氟龍絕緣
SUS304# mirror stainless steel, 1.0MM thick, sprayed with Teflon insulation
外箱材質External chamber material
鍍鋅板，噴粉，高溫塑化，1.2MM厚Galvanized sheet, dusting, high temperature plasticizing, 1.2 MM thick
電源電壓Voltage
AC380V 50HZ 9KWAC380V 50HZ
安全防護
Safety protection自動防爆泄壓裝置，防爆鏈，三色燈報警裝置，遠程控制，排煙裝置，滅火裝置等Automatic explosion-proof pressure relief device, explosion-proof chain, tri-color light alarm device, remote control, smoke exhaust device, fire extinguishing device, etc.
引線孔
Leading hole￠100mm左右各開一個，帶軟硅膠塞和不銹鋼蓋
￠100mm each opening one with soft silicone plug and stainless steel cover
拓展功能
Extension function開發(fā)通訊協議與充放電機配套使用Development of communication protocol and supporting use of charge and discharge machine
采購中心
