ＬＤ系列小型中藥制丸機的詳細資料：
小型中藥制丸機可生產蜜丸、濃縮丸、水蜜丸、水丸、丸狀食品，還可以包衣和烘干。使制成的藥丸均勻美觀。特別適用于小型藥廠、大中型藥廠試制室、中醫藥研究所、醫院、私人診所、中藥店、名貴滋補品現場加工銷售點、整機采用不銹鋼制作，符合GMP標準。且體積小，耗能低，效率高，噪音小，無污染，操作簡單，安全可靠，本機采用220V照明電，取電極為方便。
小型中藥制丸機主要技術參數:
1、功能范圍：可生產蜜丸、濃縮丸、水蜜丸、水丸、包衣、烘干及丸狀食品等。
2、制丸規格：Φ4mm、Φ5mm、Φ6mm、Φ7mm、Φ8mm
3、生 產 率：蜜丸7kg/h（以Φ5mm為準）。
4、電機輸出功率： 0.18KW、電加熱1KW
（1）電壓220V、50HZ；
（2）電壓110V、60HZ；
電機轉速1400轉/分，工作轉速50轉/分
5、適用范圍：適用于小型藥廠、大中型藥廠試制室、中藥研究所、中藥物科研究單位、醫院、私人診所、中藥店（房）、滋補品銷售柜臺現場加工及食品廠丸狀食品開發等單位。
6、外型尺寸：546×321×247mm ，
7、機器重量：30kg。
8、結構：本機由擠壓出條離合滾軸、制丸滾軸、水丸包衣器、全齒輪變速、電機、電加熱等部件組成。
9、技術特點：
（1）一機多用，拆洗方便簡單；（2）體積??；（3）重量輕；（4）性能穩定；（5）操作簡單；（6）清洗方便；（7）省電安全；（8）噪音低；（9）造型美觀；（10）與藥物接觸的部分及外殼全部采用不銹鋼，符合GMP標準。
小型制丸機詳細介紹:
一、機器使用說明
1、本機使用前，取下上蓋殼，齒輪箱蓋，必須在各油眼處滴加數滴無水分食用油，再用科研酒精擦洗四根滾軸及與藥丸相接觸的部位，做消毒處理。
2、將上蓋殼，齒輪箱蓋重新安裝復位，接通電源，打開開關，空機轉動1-2分鐘。
3、將調配均勻的團狀藥料。取適量投入擠壓槽口中，進行壓餅，然后將餅狀藥料投入出條槽中成條，再將以做成的藥條逐根橫放在制丸槽中直接搓制成丸。
4、水丸：將藥面（0.1kg）放入包衣器中，逐步放入米湯，形成粒狀后，采用間隔不斷噴淋食用水，可逐步滾制成丸。
5、包衣：待藥丸制成后，可放在水丸包衣器中，包成白色、紅色等外衣。
6、烘干方法：藥丸制成后，將藥丸進入水丸包衣器進行電加熱亦可進行烘干。以可用電吹風的熱風烘干，也可直接在陽光下曬干。
7、拋光方法：將藥丸放在水丸包衣器中，連續翻滾，滾動時間越長，表面越光滑。
二、用戶須知
1、本機適用于環境溫度為-5℃至40℃，相對濕度小于90%。周圍無導電塵埃和腐蝕金屬氣體，安放在通風、清潔的位置。
2、操作時，工作臺面應無其它無關物品。制丸機安放在穩妥的臺面上，在確認電源電壓的情況下，電源處應靠近臺面，電源插座要有可靠的接地線，嚴禁用力拉拔電源線，以防止人為翻倒，摔壞制丸機和其它事故發生。
3、本機使用后，按圖示，拆下內六角螺絲，以滾軸為界分上、下兩部分打開，取下四根滾軸，用科研酒精擦洗干凈后?；蛘吒鶕?jù)制丸需要調換規格不同的滾軸，可按圖示安裝復位。
4、在用科研酒精擦洗，調換制丸滾軸和出條離合滾軸時，必須切斷總電源，拔出電源插頭，以避免人身事故。
5、制丸機在開機使用中，嚴禁用手和毛刷或其它工具接觸制丸滾軸和出條離合滾軸，以避免扎傷手指，嚴禁在無上蓋殼，齒輪箱蓋的保護下，通電加工制丸，避免發生不必要的人身事故。
6、如遇電源線損壞（如裸線外露等），必須使用電源線。到當?shù)剞k事處維修部購買更換。如遇開關或插座失靈，必須停止使用，嚴禁變更線路繼續使用，應及時更換同規格的開頭或插座，避免發生機械、人身事故。
7、比例制作方法：蜜丸、水丸、包衣藥面拌和制作的方法詳見制丸參考配方。
8、本機配套的粉碎設備可選用本廠的LH-08B連續流中藥粉碎機。
9、水丸包衣器在不使用時，可直接拆洗向順時針方向旋轉，將其拔出即可。放在可靠、清潔的位置待使用，在水丸包衣器軸的外露部分應涂少量清潔的食用油，以防止產生浮銹。嚴禁直接用水清洗整機或電加熱器。本機不使用時，必須放置在干燥、清潔通風處。在電加熱器使用過程中，嚴禁與水接觸，以防止導電，造成電擊等人身事故。
LD series of small system of Chinese medicine pill machine details:
Small Chinese medicine pill machine can produce pills, pills, water pills, water pills, food, can also be coated and drying. Make pill uniform appearance. Particularly applicable to small companies, large and medium-sized pharmaceutical trial room, Institute of Chinese medicine, hospitals, private clinics, pharmacies, rare tonic field processing point of sale, the machine adopts stainless steel production, in line with the GMP standard. And has the advantages of small volume, low energy consumption, high efficiency, low noise, no pollution, simple operation, safe and reliable, the machine adopts 220V electric lighting, and electrode for the convenience of.
Small Chinese medicine pill machine main technical parameters:
1, functional scope: can produce pills, pills, water pills, water pills, coating, drying and food etc..
In 2, pill specifications:Φ 4mm,Φ 5mm,Φ 6mmΦ 7mmΦ 8mm,,
In 3, the production rate: 7kg/h （ pill toΦ 5mm. ）.
In 4, the output power of a motor, electric heating 1KW: 0.18KW
（ 1） 220V, 50HZ voltage;
（ 2） 110V, 60HZ voltage;
Motor speed 1400 R / min, the working speed of 50 rpm
5, the scope of application: applicable to small companies, large and medium-sized pharmaceutical trial room, Institute of traditional Chinese medicine, Chinese medicine, research institutions, hospitals, private clinics, drug stores （ real ）, tonic sales web site counter on-site processing and food factory food development unit.
6, size: 546 x 321 x 247mm,
In 7, the weight of the machine: 30kg.
8, structure: the machine consists of a clutch roller extrusion, pill roller, water pill coating device, the gear, electric motor, electric heating elements.
9, technical characteristics:
（ 1） the use of a machine, and is convenient and simple; （ 2） small volume; （ 3） light weight; （ 4） stable performance; （ 5） simple operation; （ 6） convenient cleaning; （ 7） saving safety; （ 8） low noise; （ 9） appearance; （ 10） and the drug exposure and housing all of the use of stainless steel, in line with the GMP standard.
Small pill making machine details:
One, the machine instructions
In 1, the machine before use, remove the upper cover shell, a gear box cover, must be in various oil eye drops the addend drop without water and edible oil, medical alcohol scrub four root rollers and pill contacting part, be disinfected.
In 2, the upper cover shell, a gear box cover to install reset, power is switched on, turn on the switch, the empty machine rotating 1-2 minutes.
In 3, the deployment of uniform bulk spices. Apply input extrusion notch, press cake, and then the pie spices into a groove into strips, then to make the medicine each bar across the pill tank directly twisting into the pill.
4, water pills: powder （0.1kg ） into the coating device, gradually into the soup, the formation of granular, using a constant interval of spraying water, can gradually rolled into balls.
5: to be made after the pill, coating, can be placed in the water pill coating device, wrapped in white, red coat.
6, drying method : the pills are made, will enter the water pill pill coating for electric heating or drying. To use hair dryer hot air drying, can also be directly dried in the sun.
7, polishing method: will the pill in water pill coating device, continuous rolling, rolling time longer, more smooth surface.
Two, the user information
In 1, the machine is suitable for the environment temperature from -5℃ to 40℃, relative humidity less than 90%. Peripheral no conductive dust and corrosion of the metal gas, placed in ventilated, the cleaning position.
In 2, operation, working surface should be no extraneous objects. Pill making machine placed in the safe table, in recognition of the voltage of the power supply situation, the power supply should be close to the table, the power socket to a reliable grounding, prohibit forced drawing power line, to prevent human overturned, broken pill making machine and other accidents.
In 3, the machine after use, as shown, remove the inner six angle screws, the roller is divided, two partially open, remove the four root rollers, with medical alcohol scrubbed clean. Or on the basis of pill need to change the specifications of different roller, icons can be mounted reset.
In 4, with medical alcohol scrub, replace the pill and a roller clutch roller, must cut off the total power supply, pull out the power plug, so as to avoid personal accident.
In 5, pill making machine in the boot of use, is strictly prohibited to use hands and brush or other tools contact pill roller and a clutch roller, in order to avoid finger pricks, is strictly prohibited in the cover shell, the gear case cover protection, electricity processing system pill, to avoid unnecessary accidents.
6, if the power line damage （ such as a bare wire exposed etc.）, must use special power line. To the local office of the purchase of replacement repair. In case of failure of the switch or socket, must stop using, forbidden lines change continue to use, should be replaced with the specifications of the beginning or socket, to avoid mechanical, personal accident.
In 7, the proportion of production method: pills, water pills, coating powder mixing production method for preparative reference formula.
In 8, the machine grinding equipment can select a factory LH-08B continuous-flow herb grinder.
In 9, the water pill coating device when not in use, can be directly disassembled rotate clockwise, it pulled out of. On reliable, clean location to be used, in the water pill coating device shaft exposed part should apply a small amount of clean oil, to prevent the rust. No direct water to clean the machine or electric heater. The machine is not in use, must be placed in dry, clean air. In the electric heater in the using process, no contact with water, to prevent the conductive, electric shock accidents caused by.
采購中心
