實驗用安瓿瓶熔封機詳細資料：
一、安瓿瓶熔封機概述
傳統的安瓿瓶熔封機，由控制箱和熔封臺兩部分組成，在*使用中發現有如下缺點：準備時需要臨時接插助燃?xì)獗霉?；控制箱和熔封臺擺放調節不方便；使用完畢須拔去氣管，再分兩部分提拿、搬動、收存。重復使用時，容易出現：控制臺和熔封臺配套混亂，接插不順，火焰調整不穩，丟失零配件情況。
為此，我們將兩體機改進為一體機，助然氣泵管已事先接插好，使用時，只需接通煤氣或石油液化汽，調整煤氣和助燃?xì)忾_關，即可得到均勻集中的火焰。加熱安瓿時，可緩慢旋轉圓形安瓿擺放平臺，使瓶頸加熱均勻，待軟化時，用鑷子將安瓿瓶頸上端往上拉斷，安瓿瓶頸下方即可光滑熔封。
本機工作時無噪聲，熔封速度快，準備、收存方便，整機簡潔，是醫院、制劑室、學校、科研單位、小藥廠、生物制劑廠熔封安瓿的理想設備。
二、安瓿瓶熔封機使用方法
1、連接好燃?xì)夤艿馈＃ㄔO(shè)備后面混合三通右下方針型調節閥接口）
2、插好電源線。（設備后面右上角插口）
3、開啟電源開關（設備正面右上角）
4、慢慢地開啟燃?xì)忉樞烷y，直到點著燈頭。
5、慢慢地開啟助燃?xì)忉樞烷y（設備后面左下角）直到兩個燈頭發出細長藍色火焰即可工作（火焰越細長越好）
6、按安瓿瓶放置托盤上，先不要馬上放進火焰里，首先要看火焰是否處于托盤中心點，以及是否處在你所需要熔封高度（只需松開支架上的一個旋扭就可以任意選擇，而后旋緊）
7、把灌好藥液的安瓿瓶再放到托盤和火焰的中心。左手徐徐地均勻地轉動瓶子，等燒到鍛紅色的時候，右手用鑷子把上截拉掉即可。
8、工作結束后必須先關掉助燃?xì)獾拈y門，而后關燃?xì)忾y門。
安瓿瓶熔封機主要技術參數：
1、適用規格： 1-20ml
2、產 量： 600-800支/時
3、電 壓： 220V
4、功 率： 7W
5、助燃?xì)鈮毫Γ?≥0.04KPa
6、燃?xì)鈮毫Γ?≥0.4KPa
7、凈 重： 3.2kg
8、裝箱體積： 300×180×350mm
三、安瓿瓶熔封機注意事項
1、燃?xì)馄亢腿細獍l(fā)生室必須離工作位置6m以上。
2、點火時必須先關好助燃?xì)忾y門，而一邊點火一邊慢慢地開啟燃?xì)忾y門。直到點著了之后再調節火焰的適當度。
3、燃?xì)夤芘c混合三通上的針型調節閥必須連接好，千萬不能有一點泄漏，以免發生事故。
Experiments using ampoule sealing machine details:
One, the ampoule sealing machine overview
The traditional ampoule sealing machine, composed of a control box and sealing station is composed of two parts, in the long-term use has the following disadvantages: found ready to temporarily plug assist gas pump; the control box and a sealing station is put adjustment is not convenient; after use must be pulled to the trachea, divided into two parts to carry, move, storage. Repeated use, is easy to appear: console and a sealing station supporting the confusion, plug flow, flame adjustment instability, missing parts.
To this end, we will be two body machine is improved to be one machine, auxiliary gas pump has been previously connected well, when in use, only need to connect the gas or liquefied petroleum gas, coal gas and combustion-supporting gas adjusting switch, you can get uniform flame. Heated ampules, slowly rotating circular ampoule placing platform, make the bottleneck for uniform heating, softening, the ampoule bottle with a pair of tweezers to breaking the ampoule neck below, can be smooth sealing.
When the machine works, no noise, welding speed, preparation, convenient to store, the concise, hospital preparation room, school, scientific research units, small, pharmaceutical, biological preparation factory sealed ampoule ideal equipment.
In two, the ampoule bottle sealing machine using the method
1, connect gas pipeline. （ three through the lower right behind the mixing equipment needle valve interface ）
2, plug power line. （ the rear of the apparatus on the upper right corner socket ）
3, open the power switch （ equipment the front right corner. ）
In 4, slowly open the gas needle valve, until the point of the lamp holder.
In 5, slowly open the help gas needle valve （ device behind the lower left corner ） until two light hair thin blue flame can work （ flame more elongated. ）
In 6, the ampoule bottle is placed on the tray, don't immediay into the flames, first of all depends on whether the fire at the tray center point, and is in sealing height （ you need only loosening the bracket on a knob can be arbitrarily selected, and then tighten ）
7, to fill liquid medicine ampoule bottle and then into the tray and the center of the fire. Lefty Xu Xudi uniformly rotating bottles, and other burning forging red, right hand tweezers to pull can be cut.
In 8, after work, we must first turn off the auxiliary gas valve, then close the gas valve.
Ampoule sealing machine main technical parameters:
1, applicable specifications: 1-20ml
2, yield: 600-800 / when
3, voltage: 220V
4, power: 7W
5, help gas pressure:≥ 0.04KPa
In 6, the pressure of the gas:≥ 0.4KPa
In 7, net weight: 3.2kg
In 8, a packing volume: 300× 180 × 350mm
In three, the ampoule sealing machine matters needing attention
1, gas bottle and a gas generating chamber must from the working position above 6m.
In 2, the ignition must close the auxiliary gas valve, and the side of the ignition side slowly open the gas valve. Until the later adjustable flame appropriate degree.
3, gas tube and mix three pass on the needle valve must be connected well, do not have a little leakage, to avoid accidents.
會員1.png)
