GDG20B型超級微納米乳化機

    GDG20B型超級微納米乳化機

設備介紹

該設備是由電機、底座、傳動、密封、均質器、流量泵、壓力保護裝置、冷卻、加熱裝置、控制單元等組成。物料從設備上口進入,經九級高速剪切,從下而上從上口排出。是GDG20A型的細分,定子和轉子極小的配合間隙,在轉子超速運行時產生粒子團微?；?定子面靜止,在強大的速差下,轉子高速旋轉,從而形成0.1-0.5um的薄膜,對粒徑進行切割、剝離、分層,對物料進行乳化、分散、切割等作用。

1、具有對腔室內剪切的物料進行在線保溫和加熱功能,確保物料不會過熱或過冷,滿足各種工藝要求。

2、雙端面機械密封自帶水循環冷卻和安全保護裝置,具有壓力示警保護功能,壓力值低于安全壓力時聲光報警,高速旋轉時密封更加可靠。3、采用五軸數控精密加工,保障了形位公差和尺寸公差的合格率,確保剪切定子、轉子配合間隙僅為0.15mm高速下運行順暢。高速運行的軸承溫控裝置，保證了8000r/min下長時間持續工作。

4、特殊材料保障主軸在高速運行時不會發生形變,線速度50m/s,跳動在0.05mm以內。

5、強大的剪切力、精密配合、穩定輸出的組合下,物料粒徑可達0.2-1um。

6、具有自循環清洗功能,滿足GMP要求。

Equipment introduction

The equipment is composed of motor, base, drive, seal, homogenizer, flowpump, pressure protection device, cooling, heating device, control unit, etc.The material enters from the upper mouth of the equipment, goes throughnine high-speed shear, from the bottom up, and is discharged from theupper mouth. lt is the subdivision of GDG20A type, the stator and the rotorare very small with the gap, the particle agglomeration is granular when therotor is running at excessive speed, the stator surface is stationary, and therotor is rotating at high speed under the strong speed difference, thusforming a 0.1-0.5um film, cutting, stripping, delamination of the particle size,emulsifying, dispersing and cutting the material.

1,lt has the function of online insulation and heating for the materials cut inthe chamber to ensure that the materials will not be overheated orundercooled to meet various process requirements.

2,double-end mechanical seal with water circulation cooling and safetyprotection device, with pressure warning protection function, the pressurevalue is lower than the safety pressure sound and light alarm, high-speedrotation sealing is more reliable.

3, the use of five-axis CNC precision machining, to ensure the form andposition tolerance and dimensional tolerance of the pass rate, to ensure thatthe shear stator, rotor clearance is only 0.15mm high speed runningsmoothly. The high-speed bearing temperature control device ensures long.term continuous operation at 8000r/min.

4, the special material to ensure that the spindle at high speed operation willnot occur deformation, linear speed 50m/s, beating within 0.05mm.5. Under the combination of strong shear force, precise fit and stable output.the material particle size can reach 0.2-lum.6, with self-circulation cleaning function, to meet the GMP requirements.

GDG20B型超級微納米乳化機